Full Size Arcade Help

• Hole Pattern For 2.25" Trackball Plate

  Download the file HERE. Make sure you print to size. For oversized use a 3/16 bit. For a closer hole size use a 11/64. For the oversized hole you will need a #8 washer on the bottom of most panels to keep the nut from pulling threw.

• How Do I Hook Up the 3A Trackball Intergration Board?

  Plug the 2 x 4 to pcb integration harness into: King Of Air - Plug into as pictured. 3 Sided and 2 Sided - Plug into the RED 6 Pin. Plug USB into the slot labeled TRACKBALL on the Pandora.

• How Do You Hook Up The Chrome LED or Eclipse Buttons?

  You have two parts to hook up on these buttons, the function side and the led side. To hook up the function follow these steps - On the red and black micro switch hook up the NO and the COM. The NC will not be used at all. For the LED you need to use a led harness and connect it to power. The ...

• How To Exit The Game On The Pandora 3000 / 516 in 1 Combo Board

  Product: Pandora 3000 / 516 in 1 Combo Board If you are using free play and you need to exit a game check out this video for a quick run down on what you need to do in the settings to quickly and easily exit a game!

• How To Hook Up A Standard Arcade Micro Switch

  To hook up a standard arcade microswitch you will want to use the 2 post labeled "NO" and "COM". That stands for normally open and common (ground). You will never use the "NC". That stands for normally closed and will activate the button all the time EXCEPT when you push it, at that point it deac...

• How To Install DIY Retro Arcade 12v Buttons

  To install our 12v LED buttons see this youtube help video.

• How To Remove The Sanwa Gate And Set It To 4 Way

  For product Genuine Sanwa JLF-TP-8YT 5 Pin Joystick How to Change The Gate and set to 4/8 way.

• How To Set The 18.5 Inch Bar Top LCD To English

  On the front of the machine under the marquee where the on/off switch is push the buttons in this order Menu Speaker / - Speaker / - (you will now be at a gear) Menu Bright / - Bright / - Bright / - Bright / - Menu Speaker / - until you get over English Menu Then the 2nd button on the left to ex...

• How to wire up the 25 Cent Red Push For Credit Arcade LED Button

  You need to hook the LED harness to the sides of the black bulb holder. 1 yellow and 1 black will connect to each holder. Then you use the COM and NO terminals on the red/black micro switches. The NC is not used.

• I Am Wiring Up My Sanwa, Where Do The Wires Connect For Each Direction?

  Sanwa does mater how the pcb is facing as to what wire is what. Attached is a image to help you wire your joystick.

• My Classic Ball Top Joystick Does Not Play Well On The 60 in 1. Do you Suggest a 4 or 8 Way Setup?

  Item: https://www.diyretroarcade.com/products/classic-arcade-joystick-red-ball-design-for-8-and-4-way-game-play We for the best game play on the 60 in 1 we suggest that you set this joystick to a 4 way. To do this follow these steps: 1. Take out the 4 screews on the green gate on the bottom of ...

• My Jamma Hanress Only Has One Plus and Minus Wire On #10 for the speaker, How Do I Hook up Two Speakers?

  If your jamma harness only has 1 wire on the + - for the #10 speaker wire then simply run the speakers in parallel. Run + wire to one speakers + terminal and then on the oppsite speaker hook up the - wire to the - side of the speaker then simply run a wire from the + to the - from speaker to spea...

• What Wire Goes Where On The Back Of The EMI Filter?

  See this image